PS3 Tutorials & Secrets

 :: Modding :: PS3

Go down

PS3 Tutorials & Secrets Empty PS3 Tutorials & Secrets

Post  God on Thu Jan 26, 2012 5:20 pm

Welcome To My PS3 Tutorials and Ps3 Secrets Legit :

PS3 Secrets And Tricks:

How To Browse 2 more more internet windows:

Open the browser (go to Network) and surf to a page you want. Now open up the menu with a press of Triangle and choose Open In New Window. Enter another URL and then do the same again. Keep going until youve got six windows open. Now press L3 (done by clicking down the left stick). Youre now in multi-page mode. Move the left stick to flick through the webpages as though they were bits of paper, then click L3 again to zoom in.

How To Customise your own PS3:

Try Googling 'PS3 .p3t theme' to find downloadable examplesof PS3's new Themes - the alternative desktops, menus and fonts for your PS3 that have been enabled since the recent 2.0 firmware update. Read on through this article for our tips on how to transfer them to your PS3. You can even make your ownThemes. All you'll need is Sony's PC-only design software, which is available for free

How To Boost Your WI-FI:

Slow downloads and dodgy PS3 connections? Try this... Firstly let's start with a bit of wireless networking 101. Try getting a direct 'line of sight' between yourwireless router and your PS3. Pull them out both out from alcoves and behinddense furniture and try to minimise the number of obstacles between both boxes. (Nothing degrades your Wi-Fi signal like a nice stone fireplace....)

Next, stand your PS3 on its on end. The PS3's antenna is located in the right hand side so standing itup on its left-edge gives it a bigger spread. Ideally put your router up on a high shelf.

Finally -and this is the clever bit - take a Coke can (other soft drinks are available)and cut the top off. Cut down the sides of the cup-like can and fan out thedivisions slightly so it looks like a weird metal flower. Now make a hole inthe bottom and place your new 'high-gain antenna' over your router's stubby aerialso it pokes through. Now point it at your PS3. Sounds mad, looks awful, but you could see a 10% boost in signal strength.

How to Access Playstation Recovery Menu:
]1. Turn off Playstation3.
2. Hold The power button down; The system will turn on and turn off once again.
3. Once the System has been shutdown, re-press you finger until you hear 2 consecutive beeps
4. When you hear the 2 beeps take finger off power button.
5. You will be promted to plug in your controller via usb and then hit the PS button
6. The Recovery menu will pop up

This includes On ...

Restart System:
Restarts the PLAYSTATION3 System.

Restore Default Settings:
Reset all system settings back to default.

Restore File System:
Checks for corrupt/missing system files.

Rebuild Database:
Rebuilds the OS for the PLAYSTATION3.

Restore PS3 System:
Fresh restore; Deletes everything and starts from Scratch.

System Update:
Update the PLAYSTATION3 System

Heres How To Change The Visual Player When Playing Music[Colour+Speed]

1. Fire up a song in the Audio player
2. Hit the Triangle button to bring up the Menu screen. Click on the Visual Player option and then hit Triangle to exit the menu screen.
3. Once the Visual Player starts, push Left or Right on the Right Analog stick to change scenes. Up and Down seem to change the scale and left and right the scene itself, or so it seems. Smile

How To Get The Secret Menu up That Sont Doesnt Tell Us:

usb cable
ps3[of course]
ps3 controller

1.Hold your ps3 off/on button in until it turns off,
2. when it has gone off hold the [Off/On] button again until you here 2 beeps.
3.then turn off ps3 again and wait one second
4. hold [on/off] button in until you hear 2 beeps then 2 beeps after that 
3. There You Go Secret Menu

How To Appear Offline On PS3 And Play Games Online:

By The Way This Has Been Confirmed 

How To Put Music,Videos and Pictures On Your PS3 Via [USB]

1. get a usb and plug into pc
2. put the music,videos and pictures you want on the usb
3 .when on usb go to ps3 and plug usb into the ps3
4. go to music and you will find a file saying Usb 
5. press [Triangle] and click display all
6. then hover over any song and click [Triangle] again and press up on d-pad
7. it should say copy multiple click that then to the left click select all
8. or click the ones you want to copy
9. wait untill its finished and there you go ENJOY!!!

How to Conect your iPhone/iPod Touch to your PS3 and stream media wirelessly:

1. go on your ipod and download [iMediaShare] from App Store
2. open the app once downloaded and find [PS3 VIDEO] 
3. click [PS3 VIDEO] and then click any of those videos 
4. then it will say 'Go to PS3 - Video and it should say 'iMedishare[Ipod]
5. click on it and start to use youre ipod on your ps3 to view pictures-Music and videos


How to Gamershare ps3 games and add ons Free:

1. get a friend who has the game or add on you want in his PSN store,
2. be trusted and ask your friend for his details for psn
3. recover his account and go to PSN store and go to downloads
4. find the game you wanted click download 
5. exit store sign out and wait for the download to finish
6. HAVE FUN !!

How To Patch Block Mw2/Cod4/WaW Using Elite Mossey Patch Blocker: this-Elite Mossey Patch Blocker
3.Open Up The Patch Blocker and should get an ip address Eg[]
4.Go To The PS3
6.Type In Ip Address = Eg []
7.In Port = leave 8080
8.Go Along Till End , Click X And Then Circle And Yes
9.Go To Game Game Data Utility
10.Find The Game You Want To Bypass Eg [Modern Warfare 2] 
11.Press Triangle Then Delete
12.Then Click Start Blocking on the patch blocker 
13.Then Sign In Load The Game And Wont ask you to update
14. Have Fun !!!!!!!

How To Jailbreak 3.55 PS3 [3.55 ONLY!]

1. Plug a USB stick into your computer
2. Create a folder in the root of the USB stick called PS3
3. Create a folder inside the PS3 folder called UPDATE
4. Download
5. Unzip to PS3UPDAT.PUP
6. Move PS3UPDAT.PUP to the directory UPDATE that you just created on the USB stick
7. Plug the USB stick into your PS3
8. Navigate to Settings Tab
9. Choose System Update
10. Choose Update via Storage Media
11. It will say it found Version 3.55-jb
12. Choose OK
13. Accept Conditions and Install Update
14. After less than a minute, your PS3 will update, beep 4 times then shut down.
15. Power up your PS3 (You will have to do it on the console and not by the controller)
16. Your PS3 is now jailbroken!

How to Install Custom Packages on PS3 v3.55 Firmware:

1. Plug your USB stick into your computer
2. Drop into the root of the USB stick
3. Plug your USB stick into your PS3
4. Navigate to the Game Tab
5. Choose Install Package Files
6. Select the test.pkg
7. After it installs you will find the test package from geohot installed below the Install Package Files folder
8. Wait for more packages to be created by the PS3 community

How to Replace the PS3 Blu-ray Drive Laser Lens

1) Open the top cover of the PS3.

2) Pull out the power plug for the Blu-ray drive. 

3) Carefully pull up the Blu-ray drive and unclip the data cable ribbon from PS3 drive. 

4) Remove the two silver screws on top right and bottom right according to the picture (screwdriver is pointing at them) 

5) Unsrew the 3 black screws to the left as well (screwdriver pointing) 

6) Remove the top metal sheilding of the Blu-ray drive, exposing the guts. 

7) Remove the top frame now that we are inside to reveal the laser (unscrew the screws) 

Cool Once that is done you should be staring at the Blu-ray laser. 

9) Remove the Blu-ray lens screws 

10) More screws to remove (screwdriver pointing) 

11) There you go after removing all those screws the laser should easily come out, simply repeat the process for another working Blu-ray drive and extract its Blu-ray lens or just simply buy a replacement part (part #kem-400aaa) and insert it in the Blu-ray drive and start rescrewing.

Hope this can help those unfortuante with a dead bluray drive and no warranty

Ps3 Controller LED Mod TuT:


1 x PS3 controller
1 x Wire (got mine at RadioShack its a little thick but it works, get the thinnest stuff they have)
1 x soldering Iron (lower wattage is better so you dont do damage to your board, 15w is good but will take awhile for solder to melt, I used a 25w without problems)
1 x LED (You can use the SMD LED if you can get one but RadioShack won't have these, so your best bet will be a 3mm LED. You can use a 5mm but its an extremely tight squeeze but its much brighter. I got a 3.7v 5mm LED and it worked fine, just make sure it can do AT LEAST 2.8v)
1 x Solder (doesnt take much so get a small thing of it)
1 x Tiny screwdriver for the case screws and 1 screw holding PCB to controller
1 x cup (to hold all the pieces to the controller while you're working)

Step 1

Take the controller apart. There are 5 screws holding the case together, put screws in cup. Take the back of the controller off, its snapped into place so it will take a little work, be careful though

Step 2 

Once the back is off there is 1 silver screw holding the PCB to the controller that you need to remove. It is behind the battery pack, put screw in cup

Step 3

remove PCB from controller, once removed set aside the front part of the controller

Step 4

There is a thin ribbon connector and small 4 pin plug holding the flimsy film for the buttons to the PCB, remove this from the PCB and set aside. It has the L2 and R2 attached to it, leave it that way

Step 5

Cut yourself 2 small lengths of wire and strip them at both ends. Also get your LED out and bend the wires out to the side where there is a little notch on the wires and cut them. It will make a shape like this.

Step 6

Solder 1 of the wires to the "5" hole. By this I mean take the part of the wire thats stripped and stick it down in the hole leaving a little sticking out. Then take some solder and solder directly on the wire. It will ball up just enough to also get solder on the rim of the "5" hole which will attach this wire to it (this is your ground). Next you need to take the other wire and solder it to the leg where the RED wire connects as seen in this picture

On the left side of that plug you can see 4 wires going to the board. You must solder directly to the bottom most wire. This is very delicate here so be careful.

Step 7

Once these 2 wires are soldered to the board reconnect the flimsy controller film to the PCB just through the ribbon connector (thats the wide one that plugs into the left side). Once youve done this you can take the rubber section from the front piece of the controller (the plastic piece you set aside) this is the rubber piece that has the start and select buttons on it. If you place it on the film and press down on it it should turn the controller on.

Step 8

Once you have the controller turned on you can remove this flimsy film piece again and it should stay on. You then need to take your LED and try to connect it (just by holding it in place) to the 2 wires you just soldered to the main board. This will allow to figure out which way the LED is supposed to connect (if you put it on backwards it wont light up) Once you've figured it out you should set it aside and tin the ends of the wires (this involves getting solder to build up on the wires and dry allowing you to easily solder the LED to it) Once the wire is tinned you can solder the LED to the 2 wires. If the controller is still on the LED should light up. If not check all your connections and try again

Step 9

Once this is done you should cut the clear rubber piece that sits behind the PS button (this is the clear rubber piece that fits inside the black plastic piece that the flimsy button film is attached to right in that black rubber piece that you started the controller with) You only need to cut off that tube piece that comes down on the clear rubber piece. This allows the LED to sit in that shaft directly under the PS button

Step 10

If the LED doesnt fit in the black plastic piece you must melt down or cut off the tube ( I melt mine down because you already have the soldering iron out)

Step 11 

Once this is done you can reconnect the flimsy piece back to the PCB via the 2 connectors. Carefully place it back on top of the PCB (allowing the LED to fit in the hole in the middle) There is a piece that fits into the top-left of the PCB which connects the two pieces make sure it goes in that hole. Also make sure that your wires arent blocking the plastic piece from sitting snug on the board (There are some spacers that keep the plastic piece separated from the PCB, these will sometimes hit the wires so make sure they are out of the way) Also before you put the controller back together put the analog sticks back on the PCB and make sure they have full movement without hitting the wires.

Step 12

Put the controller back together. THere is a plastic piece that separates the L1 and L2 and R1 and R2 buttons, make sure everything is slid back into place correctly, this can be difficult. Also make sure all your rubber pieces are placed back into the front piece of the controller (this includes the clear rubber piece that goes in the black rubber piece that sits behind the PS button. Once all that is in screw the PCB back into the controller, then Screw the rear piece back on the controller. And you should be done

How To Set Up/install A HDPVR Or a Dazzle On P[Detailed]S3 :


As you can see in box with HD PVR comes also some other cables. We have the long component cable, as also USB, and some AC adapter. Rest is not so imporant and it may be diffrent in diffrent versions of Hauppauge HD PVR. Prepare those cables as also some room for your HD PVR and your laptop or desktop PC.
1. Take component cable dedicated to your console and plug it into AV port on your console. There is only one port that can fit this plug so dont worry, you cant miss it.
2. After that connect the other end of your console component cable to your Hauppauge HD PVR. Insert them in your Input slots on the back of HD PVR.
If you dont know which red plug is for sound and which is for video signal, then look up closer. Almost all sound plugs in component cables have some sort of information that could help you to identify them. Sometimes they are labeled L and R (that stands for left and right sound), other times they are in diffrent color, or have some sort of plastic ring around them.
And if you still dont know- white sound is left port, and red sound is white port.
3. Connect component cable that came with Hauppauge HD PVR to output of the device. Then other end of component cable connect to back of your TV.
4. Now plug in the AC adapter and connect it to the source of power.
5. Connect your HD PVR via USB cable to your PC or laptop.
Thats all for the hardware part.

How to install Hauppauge HD PVR?

1. Press power on your Hauppauge HD PVR and run your laptop.
2. Install drivers that came on a CD with Hauppauge HD PVR kit.
3. Now when your laptop see properly HD PVR install program Total Media Extreme.
4. On your TV, when you go to the console channel (some sort of HDMI or other) on your TV, run your console and change display settings to component cable. Make sure that Hauppauge HD PVR is on when you do this.
5. Change your TV channel from HDMI (or other if Xbox 360 or PS3 was on any other channel) to channel that is dedicated to component video. It can be named AV 1-3 or EXT 1-3 or even something other. Most of the time its just simply named Component Channel.
If your TV still dont see Hauppauge HD PVR then you must power it off. Wait 3 seconds and power it on. Then your TV will see your game console video signal again.
Warrning! If you do that too slow, then your console will change video signal to the latest working again. You have like 30 seconds to do this. So it must be done quite quick.
6. After that you will need to change audio settings also. Just simply set it up to SCART/AV MULTI or any other that have 2 plugs symbol- red and white. Audio must be sent via component cable.
7. After your console is sending signal via component cable to your Hauppauge HD PVR and Hauppauge HD PVR send it to your TV you should be able to run program Total Media Extreme, and choose Record Option in first pop-up menu.
8. Now when the program loads wait 3-5 seconds. If nothing happend and you still have a black screen, just simply click the Refresh button. Now it will see console signal properly.
9. Now you can see your your Xbox 360 or PS3 menu in your computer and your TV. Your computer signal should have a little delay. Dont worry about it. This delay its just a view delay. Recording will be syncronised.
10. Now select format settings. You now can choose your bitrate. If you wanna record gameplay in HD you should set it up to maximum, thats 13,5 Mbits. Of course if bitrate is bigger then the record clip on your PC is also bigger, but for recording in HD you should make some room.
11. Now choose the best recording format for your console. If you have a Playstation 3, then choose PS3 option. If you have Xbox 360, then choose it. If you are playing on any other console or you are recording video from other device (like blu-ray player, dvd player, vhs, beta etc) you should use AVCHD or try PS3, XBox 360 settings, and use the best for you.
12. Thats almost all. You can optional change destination of your recordings. And when you done that, then you are ready for recording. The settings will autosave after first configuration, so dont worry. You can change them whenever you want in the future also.

How To Speed Up Downloads On PS3:

Find your computer's IP address in the Control Panel -> Network Connections. This is probably something like If it does not start with 192.168 then you might have a public IP and this won't work (at least not easily).
Download Privoxy from their website:
Run the Privoxy installer. When it is done the Privoxy window should appear.
Go to the Options menu and select 'Edit Main Configuration'
Find the line that says "listen-address". Should be about halfway through the file.
Replace with the computer's IP address (should start with 192.168). The :8118 part should stay.
Save and close the configuration.
If you have a firewall on your computer you need to allow access to Privoxy on port 8118.
On the PS3 open the network configuration settings. When it asks if you want to use a proxy say yes and enter your computer's IP address and port 8118.
ake sure the connection test works first.

How To Set Up A Playstation Media Setver:

Download Link: Download For Media Server Setup

All About Playstation 3

PS3 Info

The PlayStation 3   ( abbreviated as PS3) is the third  game console created by Sony and the successor to the PlayStation 2 as part of the PlayStation series. The PlayStation 3 competes with Microsoft's Xbox 360 and Nintendo's Wii as part of the seventh generation of consoles. It was first released on November 11, 2006 in Japan, with international markets following shortly thereafter.
Major features of the console include its unified online gaming service, the PlayStation Network, its robust multimedia capabilities, connectivity with the PlayStation Portable and its use of the Blu-ray Disc as its primary storage medium

Ps3 Errors

0710102 - DNS Error (DSN Server Isn't Available) 

8001050B - Will Not Play Demo Games Installed On The Hard Drive When Blu-Ray Disc Is Inserted. 

80010510 - Will Not Play Games Installed On The Hard Drive. 

8002B241 - DVI Has No Audio. 

80029023 - Exchanging Key Information Exchange Has Timed Out. 

80029024 - The Attempt To Obtain An IP Address Has Timed Out. 

80029564 - Downloaded Game Will Not Install. 

8002F997 - Can Not Update XMB Firmware. 

8003051E - Game Will Not Save. 

80031150 - System settings fail to save (Setting information is corrupted. Press the X button to repair and restore default..) 

80130203 - PS3 connects to the Internet but not to the Network (Usually means that the required ports are not open.) 

80710092 - An error has occurred. you've been signed out from the ps network (Your Internet connection may have dropped.) 

80710102 - PS3 Cannot connect to the router with current IP information (Try rebooting your router.) 

80710541 - The Connection To The Server Timed Out. 

80710B23 - PS3 Network Is Down Or The PS3 Network Is Too Busy To Respond. 

80710D23 - Turn the PS3 off for approx. 30 minutes with the power toggle, not standby mode. 

80029024 - Cannot Obtain An IP Address. 

8002F997 - Trying to update the Firmware, copying to a file and installing from a USB drive failed. 

80710016 - Playstation Network Is Down. 

8013013E - WEP Key error, change WEP key to all numbers (on router homepage) and try again, or switch to WPA. 

8071053D - Hard boot the PS3, turn off the PS3 to stand-by, flip off the back switch and completely remove the power cord. Shut off your modem/router, for approx. 5 minutes, then turn the modem back up first and let it sync. Then turn the router back on (if you're using one) and let it sync. Reconnect your power cable and flip the back switch up again. Then make a new network connection. 

8013030F - Check Router Page, SSID Broadcasting possibly off. 

8002F994 - Too many people downloading the update (download it later on.) 

80028F10 - Go to Display Settings then HDMI (or whatever your connection is) and instead of Custom choose Automatic. 

8002A705 - Unable To Connect To Server/Host (Check Router Port Configuration.) 

80030920 - An error occurred during the copy operation, the file may be corrupt or there isn't enough memory (Try copying data from original source.) 

80029945 - Cant Playback Burn BDr Movie. 

8013030 - System Error Due To Failed Update Download. 

80010001 - Major Error , Game Ability Stopped. 

80010017 - Can't Start Blu-Ray Game. 

80010516 - An error occured during the start operation; Ps1 game swapped using the eject function and then play pressed quickly, ps1 game inserted again. 

80031601 - Error Creating Account. 

80410418 - DNS Error. 

80710101 - Conneciton Error. 

80710102 - IP conflict , PS3 Cannot connect to the router with current IP information - Try rebooting your router. 

8071040C - The PSN is handling too many connections, reboot PS3 and try again. 

80710723 - Possible Port Error - Try opening ports , TCP port: 80, 443, 5223 and UDP port: 3478, 3479, 3658. or add PS3 to DMZ. 

81019002 - Error copying saves from location A to location B not open to connect to store but PS3 can connect to internet. 

8001050D - An error occured during the start operation; Ps3 game swapped using the eject function and then play pressed quickly - ps3 game inserted again. 

80028EA5 - Unknown?? User cannot connect to PS3 network. Sony told the user to send the machine in. 

80028EA6 - Connection error , Possible Proxy error power cord. Then shut off your modem/router, for about 5 mintues, then turn the modem back up first and let it sync, then turn the router back on(if using one) and let it sycn. Reconnect your power cable and flip the back swtich up again. Then make a new network connnection. 

80028F17 - Ps2 disc Boot Error , An error occured during the start operation; Ps2 game swapped using the eject function and then play pressed quickly - Backup ps2 game inserted again (ps3rips). 

80028F18 - Ps2 Disc Error, unsupported disc; eg. Utility discs, BB discs, IQ Remix game etc. ode). 

80028F19 - PS2 Disc Error , fsck; the internal PS2 disk got corrupted and I guess that you can use HDD utility disc to fix it. 

80028F1A - Ps2 Disc Error , invalbnnetcfg; network config error. 

80029C68 - Corrupt Data Usually On External Device. 

8002A10D - Unable To Add Friend In XMB. 

8002A4A6 - Cannot Load Game To Play Online. 

8002A515 - Error Signing In. 

8002A548 - Unable To Remain Logged In - Either To Game Or Server. 

8002a71A - Possible NAT Error , Can log onto Game Server but can't join game and can't host game. 

8013013D - "A connection error has occurred" - May be to do with the SSID of the Router or signal strength if the conneciton drops Putting the PS3 into DMZ may help - otherwise check WPA key Ps3 can't handle WPA2 only WPA or none. 

8013030F - Access Point Not Detected. 

80410A0B - Internal PSP error, hardware fault. Send back to be replaced/fixed. 

807101FF - An error occurred during communication with the server. This is a DNS error. 

80029513 - Copyright Violation When Attempting To Install Game. 

80010514 - Disc Error Detected. Retrying Operation. 

80010036 - an Error Occurred uring The Delete Operation Error. 

80010014 - Has to do with downloading from the PSN, When you have bought a game and this error occurs, please go to your "recently downloaded/purchases" to download it first try. 

8002F147 - Cannot update the firmware, Possible solutions, turn off proxys, try not using a firewall, and/or turn off UnuP support. 

80029C9C - The Data Type Is Not Supported. 

80010029 - So far it only happens during data transfers... I called sony and they said that it is a NEW code and they dont know anything about it. It seems like anything to do with formating the ps3 has this error code! 

0710102 - DNS Error (DSN Server Isn't Available) 

80023121 - PSN Server Error 

80710A06 - PSN Is Down For Maintenance 

8002A227 - Console Banned. This Means 30 Day Or Perma Ban Depends If You Got Once+ Infractions 

80029945 - Cant playback burn BDr movie <--- it can be solved installed Cyberlink PowerProducer plug-in for Sony drive first then burning the disc.


Part 1 : 

Part 2 : 

Part 3 :

These are not my videos.

Credit to "God"


There has probably an unexpected maintenance currently started try in a hour or 2 then you should be up and running again.

The 80022D86 ERROR CODE?

This is fine this means your trophy data is currently corrupted.

1.To fix this Enter Safe mode
2.Select Restore File System

Any More Problems This Will Help You:

How to report players id:

You can report users who are not on your players met list by going to the PlayStation website and using the Grief reporting page here
You will have to enter some details

PlayStation website:

Update does not complete install: 

Use a different HDD this may work.

Blu-Ray discs Cants Be Read:

Replacing the laser has been known to fix this issue. Send you console to the nearest console repair or use your warranty to get it fixed.

Disc is auto-ejected:

Just Stay connected to the Internet their may be a problem with your connection.

Black screen when loading games via disc:

 If downloaded games from the market and they can still be played then it is most likely a disc read error to resolve this either try a new disc or get the lens replaced.

No longer able to use Ethernet/WiFi: 

Just restart the router/modern this is a common error.

Starting to splash screen/blank screen:

 Buy a new Hard Drive this has been known to solve this issue. 

In-game XMB not showing:

 Just make sure its actually a PlayStation 3 game not any other formats(Xbox,PC etc) 

I Think Its Freezing

A Massively Occurring Problem in inwhich freezing comes across as a performance error experienced by most PlayStation 3 owners. In case of of their problem by, pressing and holding down the power button until the console shuts down normally resolves this problem

I Think My Playstation is Overheating

Poor ventilation may very well be a cause for this, which it normally is.Make sure that your console area is very well ventilated and more importantly,Your PlayStation 3 is kept well away from hot areas. 
Gold Member
Gold Member

Posts : 139
Points : 227
Swag amount : 1
Join date : 2012-01-25
Age : 23
Location : My Crib

View user profile

Back to top Go down

PS3 Tutorials & Secrets Empty Re: PS3 Tutorials & Secrets

Post  iPhone-4 on Sun Jan 29, 2012 11:53 am

Nice tut man!
Casual Poster
Casual Poster

Posts : 124
Points : 187
Swag amount : 2
Join date : 2012-01-25
Age : 22
Location : Michigan City, IN

View user profile

Back to top Go down

PS3 Tutorials & Secrets Empty Re: PS3 Tutorials & Secrets

Post  God on Mon Jan 30, 2012 12:15 am

iPhone-4 wrote:Nice tut man!
Thx. Smile
Gold Member
Gold Member

Posts : 139
Points : 227
Swag amount : 1
Join date : 2012-01-25
Age : 23
Location : My Crib

View user profile

Back to top Go down

PS3 Tutorials & Secrets Empty Re: PS3 Tutorials & Secrets

Post  Sponsored content

Sponsored content

Back to top Go down

Back to top

- Similar topics

 :: Modding :: PS3

Permissions in this forum:
You cannot reply to topics in this forum